Your partner for astronomy
Subscribe to RSS Feed or ATOM Feed

New: Diamond Steeltrack focuser with Steeldrive from Baader

June 17 2019, Stefan Taube

Diamonds really are astronomers’ best friends – at least since the Baader Diamond Steeltrack focuser has been available. It uses real diamonds in its drive system!

In contrast to conventional Crayford or rack-and-pinion focusers, the Diamond Steeltrack’s micronized drive system guarantees entirely backlash-free operation, is completely non-slip and torsion-free – and has a vertical load capacity of 6 kilograms!

Okularauszug Diamond Steeltrack an einem Celestron EdgeHD

Diamond Steeltrack focuser on a Celestron EdgeHD telescope

There are Diamond Steeltrack focusers available for Schmidt-Cassegrain telescopes, Newtonian telescopes and refractors.

The Steeldrive II motorized focuser drive with hand-held controller is now available:

Baader Fokussiermotor Steeldrive II mit Steuerung

Baader Steeldrive II motorized focuser drive with control unit

The Steeldrive II motorized focuser drive permits automated focusing of a telescope via computer, as well as precise and vibration-free focusing using the buttons on the hand-held controller.

A good focuser considerably enhances observing pleasure and is essential for high-end astrophotography. The Steeltrack focuser is currently the best possible solution available!

 

Infographic: The Astronomy Highlights of Summer 2019

June 3 2019, Marcus Schenk

Summer and warm temperatures: now all those who were hibernating in the winter can venture outside for a glimpse at the stars. But unfortunately it also gets darker later and then, as if turbocharged, light again just a few hours later. So you need to make good use of the hours of darkness, because when the summer Milky Way stretches across the sky there’s so much to discover.

The new astronomical infographic “Highlights in the Summer Sky” shows you at a glance what is happening in the sky in the months from June to August. Also included: a short description of the events.

June 5: The Moon meets Mars

Just two days after the new Moon, the slender crescent Moon stands seemingly fragile as dusk falls in the evening sky. Inconspicuous at around 2.5 degrees further to the right you will find the 1.7 magnitude bright Mars.

June 10: Jupiter in Opposition

You can now observe the largest planet in the solar system all night. Jupiter is in opposition this month, so this is the best time for observations. The gas giant reaches a magnitude of 2.6 and is 640 million kilometers away. As night falls the planet emerges above the horizon in the southeast, later it quickly becomes brighter and gets easier to see. At around 1:15 CEST it reaches the meridian and is particularly good to see.

June 18: Mercury Half Phase

Mercury reaches dichotomy, that is, a phase in which it is half-lit. Like the Moon or Venus, Mercury displays different phases.

June 18: Mercury meets Mars

A very beautiful event takes place shortly after the middle of the month: a close encounter between Mercury and Mars. Our innermost planet passes Mars at a distance of just half a lunar diameter, 13 arc minutes. This event takes place just above the western horizon at around 21:30 CEST. To observe these two it’s best to use binoculars.

June 19: The Moon meets Saturn

This configuration takes place in the second half of the night and can be followed until sunrise. Our Moon and the ringed planet approach each other with a minimal separation of about 2°50′.

June 24: Mercury’s greatest eastern elongation

Mercury gradually leaves the evening sky but it can still be seen, and can initially be found with the naked eye. From the second half of the month it becomes more difficult to find since it is so faint, and you’ll need the help of binoculars. It reaches its greatest angular distance of 25° from the Sun on 24 June. It reveals an almost half-lit sliver to us with a size of 8 arcseconds..  You can find Mercury with a good pair of binoculars from around 22:00 CEST.

July 2: Chile Total Solar Eclipse

In South America the Sun will grow dark. The eclipse’s shadow comes from the direction of the Pacific Ocean and stretches across Chile with a totality duration of 2:30 minutes. Later, the shadow moves onwards over Argentina. The Sun will be relatively low during this eclipse which will enable beautiful shots of the eclipsed sun against the landscape.

July 5: Noctilucent Clouds

Now in June you will be able to see them: noctilucent clouds. When the summer Sun is between 6° and 16° below the horizon it sometimes illuminates extremely thin clouds of ice crystals that are at an altitude of about 80 kilometres. These clouds are indeed so high that they are in the mesosphere part of our atmosphere. For us it is long since nightfall, but these clouds catch a little sunlight and we see bluish white clouds illuminated, which are invisible by daylight.

July 9: Saturn in Opposition

At present we have the problem that, due to the Sun’s ecliptic, many planets are far to the south and so are not high enough in the sky to be visible. Because of this we inevitably face a struggle with air turbulence. Despite this, Saturn still is worth observing, even if it only climbs to a height of 18°. On July 9 it reaches its opposition and shines brightly in the sky with a magnitude of 0.1. It is competing with the brightest stars but we can recognise it by its yellowish colouring and a faint glow that differs from the flickering of the stars. Because of this you can find it straight away and you can easily capture it with a small telescope. Its rings appear tilted at 24° and we are looking from the north at the ring system in which we can easily recognise the Cassini Division.

July 14: Pluto in Opposition

Pluto is a hard-to-see dwarf planet that used to be classified as a planet, and can barely be distinguished from a star – at least if you don’t have a map at hand. Even so, it’s worth taking a look at this outpost of the solar system with a larger telescope. GoTo coordinates: RA: 19h33m40s, DEC: -22° 07′.

July 16: Partial Lunar Eclipse

In January we had to view this in the cold, but not today. We can observe this partial lunar eclipse in warm temperatures and at a reasonable time. It gets interesting for us at 22:01 CEST, at which point the Moon enters the umbra of the Earth. Over the course of the evening it will become up to 66% obscured before the umbra moves away again and eventually disappears at 1:00 CEST.

July 20: Moon Landing 50th Anniversary

50 years ago today the whole world looked towards the Moon: to three astronauts, pioneers of humanity, who dared to set out on the greatest adventure. Apollo 11 flew to the Moon and Neil Armstrong became the first person to set foot on a foreign celestial body. Let us celebrate this event, remember it, and look again today towards the Moon, perhaps even to the Sea of Tranquility, the landing site of this daring mission.

July 29: The Delta Aquariids

A small meteor shower in Aquarius which we can best observe after midnight. The Earth passes through trails of small dust particles which burn up when entering the atmosphere and become streaks of light. We can expect to see 20-25 meteors per hour provided we find a dark place for our observation.

August 9: The Moon meets Jupiter

Similar to in July, the Moon and Jupiter meet again today. When it gets dark they stand dominant and bright in the sky above the southern horizon.

August 10: Mercury’s greatest western elongation

Now Mercury reaches its greatest angular distance of 19° from the Sun. Whilst before it was an object of the evening skies, for around 10 days from today we can discover it in the morning sky. On August 10 Mercury rises at 4:30 CEST, it then disappears into the haze, then it rises higher and we have a good chance of seeing it in the sky around 4:50 CEST.

August 12: The Moon meets Saturn

We have almost full Moon, so the sky is brightly lit, but Saturn shines clearly visibly and just 5° from the Moon. If our gaze wanders a little more to the right and a few degrees higher, we will also find Jupiter.

August 12: The Perseids

Every year we look forward to the most beautiful shooting stars of the year: the Perseids. In the morning of August 12 the meteor shower reaches its peak. Up to 100 shooting stars per hour rain down, thundering through our atmosphere at incredible speeds of around 216,000 km/h. The peak will be reached between 22:00 CEST and 4:00 CEST. Unfortunately this year the almost full, and far too bright, Moon will disrupt the display so that we are likely to only be able to observe the very brightest shooting stars. It’s best to find a spot away from the direct glare of the Moon. We have the comet 109P/Swift-Tuttle to thank for this meteor shower, which lost part of its mass on its orbit around the Sun. Whenever the Earth crosses the orbit of the original comet in August, the Perseids shoot across our corner of the sky.

August 23: Occultation of the Hyades by the Moon

Unfortunately, it’s not until the early hours that we can observe an interesting occultation of the star 61 Tau by the Moon. Such occultations of the Hyades star cluster are particularly interesting because it contains many bright stars and we can sometimes even see multiple occultations. Around 4:40 CEST the Moon approaches from its illuminated side and snuffs out the 3.7 magnitude bright star. The star remains hidden behind the Moon for a little more than an hour. At 6:00 CEST, as if out of nowhere, it suddenly reappears. Important: point your telescope at the Moon a few minutes beforehand to ensure you don’t get the timing wrong.

August 27: Occultation of Delta Geminorum (Wasat) by the Moon

The Moon has migrated to the next constellation in recent days and is about to enter its new Moon phase. Before sunrise, it occults a really bright star: this time the double star 55 Gem in the constellation Gemini. The Moon, at this stage just a thin sickle-shape in the sky, approaches from its illuminated side. At 5:50 CEST the time has come: the star disappears behind the Moon and reappears nearly an hour later at 6:40 CEST. But by then the Sun has long since risen, the sky is bright and so the reappearance is difficult to observe with a telescope.

Now available: the GreenLine roll-off roof observatory from DomeParts!

May 21 2019, Stefan Taube

We are pleased to offer the roll-off roof observatory GreenLine from DomeParts GmbH – now available at a great price. You can now realise your dream of having your own very own garden observatory. It’s also perfect for astronomy clubs.

The Greenline roll-off roof observatory is available in three sizes:

The larger size GreenLine Plus is perfect for astronomical organisations.

DomeParts GreenLine

A GreenLine observatory in the exhibition area of the astronomy fair AME.

The advantages of a roll-off roof observatory compared to a classic dome observatory are clear:

  • The observatory looks like a typical garden shed and so blends in perfectly in any domestic setting. The wooden GreenLine is not only well-designed, but looks great too.
  • The roof can be fully retracted giving you an unobstructed view of the sky in every direction.
  • The inside of the cabin adjusts quickly to the ambient temperature, eliminating turbulent air currents which can often arise with a dome opening.
DomeParts GreenLine Omegon

GreenLine observatory with an Omegon RC on an iOptron CEM60 mount.

The open roof of the roll-off roof observatory offers plenty of room to manoeuvre even for a large-aperture telescope. Here in the picture the GreenLine observatory is equipped with an Omegon RC Truss telescope on an iOptron CEM60 mount.

The delivery time for a GreenLine roll-off roof observatory is around one month. You can put the observatory together yourself or let our construction team build it for you.  Get in touch with us: We’re happy to give you advice and provide you with a quote.

iOptron mounts: A new addition to the CEM family

April 4 2019, Stefan Taube

CEM series mounts from iOptron are already widely used in the US and are becoming increasingly well known in Europe too. The CEM25P mount for portable astrophotography with Newtonian telescopes of up to 6 inches aperture and the CEM60 mount for use in observatories have proved particularly popular.

With their new CEM40 and CEM40-EC with encoders, iOptron now provides a middle range mount capable of carrying loads of up to 18 kilograms. The CEM40 is hence ideally suited for astrophotography with telescopes of up to 8 inches (200 millimetres) in aperture.

iOptron CEM40

The CEM40 is the latest addition to iOptron’s CEM series

The abbreviation CEM stands for centre-balance equatorial mount, i.e. for equatorial mounts which are supported at their centre of gravity. This design ensures an excellent relation between weight and carrying capacity. The CEM40 weighs only 7 kilograms and yet can carry OTAs up to 2.5 times heavier. The amazing carrying capacity of CEM mounts has been constantly reaffirmed by our customers – especially regarding the CEM25P.

The CEM40 comes equipped with an electronic pole finder, known as ‘iPolar’. A laptop is required to operate this however, so the CEM40 is particularly suitable for astrophotographers who already use a laptop for their camera. iPolar and built-in GPS provide easy and accurate alignment and GoTo computer control initialization.

The encoders installed in the CEM40-EC version ensure very high GoTo accuracy and allow worm gear permanent periodic error correction – a problem that all mounts suffer from. The CEM40-EC does away with the need for guiding with your astrophotography.

The CEM family now covers a wide range of load carrying capacities, offering a suitable model for every budget!

New: NB1 nebula filter from IDAS

March 25 2019, Stefan Taube

Luminescent emission nebulae, supernova remnants and planetary nebulae are all particularly beautiful objects pertaining to the night sky. This applies both to the simple process of visual observation, as well as to astrophotography. Nature illuminates such nebulae in specific spectral colours: the red light of hydrogen, the blue-green light of oxygen ions and also in the colours of sulphur and nitrogen ions.  Nebula filters enable these colours to pass through whilst blocking the diffused light of the natural luminance of the sky and of light pollution. The result is a marked increase in contrast.

With the Nebula Booster NB1, the filter specialists IDAS are introducing a new, very high-performing filter of this type onto the market, and one that is not overly expensive! As the transmission curve shows, the filter has high transmission and is permeable for all relevant spectral lines, with a surprisingly narrow passband: A real nebula intensifier!

Transmission curve IDAS NB1

 

The filter is ideal for photographing large nebula regions since it enables the typical colours of these objects to pass and blocks the disruptive skyglow. The filter quickly and completely cuts off near infrared up to 1100 nanometres. This is important since cameras are sensitive to this range, but telescopic lenses are optimised for the visible spectral range and are faulty in the infrared range.

IDAS Nebula Booster NB1

IDAS Nebula Booster NB1

 

The Nebula Booster NB1 is available with two versions which cover both of the common filter thread sizes and can be screw-fitted to the housings of eyepieces or cameras.

New focus motor for Celestron telescopes (1 Comment)

February 26 2019, Stefan Taube

When it comes to astrophotography, the right focus is the most important thing. Even the best optics only deliver sharp images if the focus is spot on. A motorized focus has two advantages over manual focusing: it is vibration-free and very precise. If you remotely control your telescope via your PC, you definitely need motorization.

For the very popular SC telescopes of the Celestron brand, numerous solutions from different suppliers have been available. Celestron now offers its own model, the focus motor for SC and EdgeHD optics.

Celestron Fokussiermotor für SC- und EdgeHD-Optiken

Celestron focus motor for SC and EdgeHD optics.

The motor fits all SC, EdgeHD and RASA optics, as well as the two new Maksutovs with CGEM-II and CGX mounts. Exceptions are optics built before 2006 and the 9.25″ EdgeHD. An additional adapter is required for the RASA 1100, as the RASA 1100 is already supplied with a FeatherTouch micro-focus. The adapter requires you to dismantle the focuser partially to fit the motor.

If you are using a Celestron mount, power is simply supplied via the mount’s AUX port. A cable for this is included in the scope of delivery. If all AUX ports on your mount are already occupied, simply use the Celestron Aux Port Splitter.

The motor can be controlled in three ways:

  • With the NexStar+ controller: Simply press the MENU button, select Focuser and you can use the two arrow keys to control the motor and adjust its speed. Version 5.30+ of the installed firmware is required. You can update your Nexstar control via the Internet at any time. The controller is not only suitable for visual observation, but also for astrophotography with a DSLR, i.e. without a laptop.
  • With a laptop or PC: If you operate your telescope remotely or have connected an astrophotography camera, it is best to use the free program Celestron Focuser Utility for Windows. For this purpose, you need to connect the NexStar hand controller to the computer via USB, not the focus motor itself. The new CGX and CGX-L mounts can be controlled with the Celestron PWI software. The focuser can also be addressed via this program. The CGX and CGX-L mounts can be connected directly to the laptop or PC via USB without manual control.
  • Without a Celestron mount: If you have a Celestron optic mounted on another brand’s mount, you can control the focus motor via the USB port. The USB port should supply 900mA. As an alternative to the USB power supply, you can also operate the focus motor via main power or a Powertank. However, a power supply unit or power cable is not included in the scope of delivery.

The Celestron focus motor for SC and EdgeHD optics is a really useful accessory that is easy to adapt and operate.

Improved Version of the Dobson LightBridge by Meade

February 7 2019, Stefan Taube

No other telescope produces the natural experience of the night sky as directly as a Dobson. Completely without a camera or any other electronic deflection – armed only with an infra-red lamp and star chart – discover nebulae, star clusters and galaxies.

Apart from good weather, two things are necessary to enjoy observation: As large a telescope as possible and a dark night sky. A Dobson is a reflector telescope with a relatively simple base. So, for your money, you’ll get a telescope that is bigger than others. The problem with the dark sky is, however, more difficult to solve. The Dobson telescope should fit in a car so you can drive to a good location for observing.

A large telescope that fits in a car is a contradiction in itself. This is resolved by the Dobson wire-mesh tube:

Gitterrohrdobson

This Dobson in the LightBridge series can be taken apart without tools.

As the figure shows, the telescope can be taken apart into relatively small parts. From left to right, you can see the rocker box, the mirror case, the tube rods and the carrier ring with the secondary mirror. On location, the truss tube Dobson can be built in a few minutes without any tools.

The manufacturer, Meade, was one of the first, with the Dobson telescopes in the LightBridge series to use this form of construction and at a price that is affordable for amateur astronomers. We can now offer the improved version, the LightBridge Plus.

Meade Dobson Teleskop N 254/1270 LightBridge Plus

Meade Dobson Telescope N 254/1270 LightBridge Plus

The new LightBridge Plus has an improved rocker box. It is somewhat lighter, has notched carry handles, a pre-installed eyepiece tray and a friction brake for the height axis. The box can be taken apart without tools so it can be easily transported. Meade now fits these telescopes with an improved eyepiece holder that has a fine-adjustment knob for precision focusing and comes with a high-quality 2-inch eyepiece with a 26-mm focal length.

As with the previous version, the LightBridge Plus has a main mirror fan for faster alignment of the mirror with the ambient temperature. As expected, the optics are fully adjustable. Thanks to the fast aperture ratio, the tube is relatively short and the viewing height at the zenith is not too high.

If you’ve always wanted a telescope with a large aperture, but just didn’t know how you’d carry it around, a LightBridge Plus is a very good choice at a fair price!

 

Is a Dobsonian telescope right for me? | with product recommendations

December 30 2018, Marcus Schenk

A simple Dobsonian or a GoTo telescope? – a question whose answer you first have to decide on. You should also choose your telescope based on what you would like to observe or experience in the night sky.

Did you know that there is also a system with something like ‘a bit of GoTo’?

But how do you find out if a Dobsonian telescope is right for you? In Part 1 of this post, we’ve put together a few questions to help you find your preferences.

Following on, in part 2, there are product recommendations for three different telescope series, with you can use to explore the night sky.

 

Part 1

Are you an observer for whom a Dobsonian telescope is suitable? Or do you need a telescope with an equatorial mount? Decide which using the following questions:

 

1. Do you only want to observe or also to take photos?

There are two types of observing: the visual and photographic. Which do you prefer? If you are a visual observer, then a Dobsonian would probably be the right choice.

1 Yes I want to observe visually.
2 I do not know yet, maybe both.
3 Taking photos is more important to me than observing visually.

 

2. What do you value more? – the optics or the mechanics and electronics?

Dobsonian telescopes consist of a wooden box with plain bearings, called a ‘Rockerbox’, and a Newtonian mirror OTA. A clear emphasis here is placed on a larger OTA diameter. The mechanics remain simple. The advantage – you get a large aperture telescope for relatively little outlay, with which you can observe a lot.

1 I put more emphasis on a great optics for a low price.
2 I cannot commit myself, maybe both.
3 I am a fan of complex mechanics that controls my telescope via slow motions and worm gears.

 

3. Quick assembly or precise alignment?

Dobsonian telescopes consist of only two parts. The advantage – just two parts can be quickly transported and reassembled at the observing site. They are often much quicker to put together than a telescope with a tripod, equatorial mount, several counterweights and the OTA itself. You do not have to align a Dobsonian telescope to the celestial north pole, you are tracking in both axes’ directions.

1 I want to set up my telescope quickly, I can’t be bothered with all the complexity of assembling and observing with an equatorial set up.
2 I would like to have GoTo, but only if the setup does not take too long.
3 I’d rather spend more time putting the system together and precisely aligning it.

 

4. Do you prefer observing the Moon and planets, or observing galaxies?

A medium to large Newtonian telescope is of course also suitable for planetary observing. But the strengths of a large mirror lie in its greater light-gathering power. This makes many Dobsonian telescopes suitable for observing nebulae and galaxies. Bu if you are more interested in the Moon and planets, then a refractor telescope would be the better choice.

1 I want to observe nebulae and galaxies.
2 I want to observe nebulae and galaxies, but how am I supposed to find them?
3 I am interested in the Moon and the planets, but there is so much light pollution where I live that I cannot observe galaxies very well. An automated telescope would have to find them.

 

5. Exploring the night sky with a star map or using a GoTo system?

Dobsonian telescopes are almost always manually controlled instruments. In other words, there is no GoTo system here that slews to objects at the push of a button. You have to guide the telescope purely manually to the object of your choice with the help of a star map and then track it manually. But what is the advantage of that? Quite simply – the night sky will eventually become your familiar hunting ground that you know like the back of your hand. You’ll become a real expert at finding deep sky objects. And you will develop a feeling for tracking objects. The other thing is that it’s a lot of fun, and every time you find an object there is that little thrill of achievement.

1 Of course, I want to find the objects myself using a Dobsonian telescope.
2 I’m afraid that I’m not so good at orienting myself.
3 I’m not really interested in star hopping – there are GoTo telescopes for finding astronomical objects.

 

6. Naturally experiencing the night sky using only a little technology?

Observers repeatedly report that they can enjoy a natural experience to the maximum with a Dobsonian telescope. There is no complicated technology here that needs to be made to work. No, naturally experiencing the night sky without any motor noise is the most important thing.

1 I want to visibly experience the night sky in a clear simple and natural way.
2 I would like to be able to to add a little technology if I want.
3 No, this manual control idea is not for me. State-of-the-art technology and GoTo systems would be my first choice.

 

Your answers

If you answered most questions with a 1, then you are definitely a ‘Dobsonau’. You should immediately buy a Dobsonian telescope – perhaps one of the three examples detailed below?

If you’ve answered most questions with a 2, then you’d like to observe with a Dobsonian, but GoTo systems also tempt you. The Onmegon Push+ Telescope with object navigator (see below) would be the way to go.

If you answered most questions with a 3, then you’d better use a GoTo system. Here, we have a large selection.

 

Part 2

We have three Dobsonian telescopes in our program: the Omegon Advanced X Dobsonian telescope for beginners, the Omegon ProDob for intermediates and experts and the Omegon Push+ with push-to-technology.

 

Omegon Advanced X Dobsonian telescope – for getting into deep sky observing

These telescopes are a great way to start visual deep sky observing. Explore star clusters, hydrogen nebulae, planetary nebulae, and even galaxies with their spiral arms. With a 200mm lens aperture, this telescope will show you hundreds of interesting objects. If you want even more light, you can also use the Omegon Advanced X N 254/1200 or a real ‘light cannon’, the Omegon Advanced X N 304/1500. Of course, ‘excursions’ to the Moon and the planets are also possible.

If you do not want to spend a lot of money, but are looking for a great value-for-money telescope, then an Omegon Advanced X is the instrument for you.

Omegon Advanced X 203/1200

The Omegon ProDob – deluxe Dobsonian with an excellent friction system

ProDob Dobson telescopes come with a particularly good 2″ Crayford focuser and a deluxe friction system. Once an object is centred in the eyepiece, tracking is even more accurate and precise – even at very high magnifications. There is no juddering or anything (as with instruments with Teflon bearings), as when slewing the telescope it almost floats to the next object. The reason for this is a ball-bearing system in the elevation axis and roller-bearings in azimuth. And also, the friction level can be set to your needs. High magnifications are also possible with a Dobsonian.

Omegon Dobson Teleskop ProDob N 203/1200

The ProDob from Omegon comes in a range of apertures:
– ProDob N203/1200 with 8“ diameter
– ProDob N254/1200 with 10“ diameter
– ProDob N304/1500 with 12“ diameter
– ProDob N406/1850 with 16“ diameter

 

Omgeon Push+ – control a Dobsonian telescope using your smartphone

With the Omegon Push+ Dobsonian, you can travel to the planets, nebulae and galaxies in the universe whenever you wish. You do not even need to be very knowledgeable about the night sky, because the telescope guides you using a push-to-system to any object you wish to observe. All you need is an Android smartphone and the SkySafari 4.0 app.

The Omegon Push+ and Push+ Mini telescopes bridge the gap between a purely manual Dobsonian and a GoTo telescope. So to speak: ‘A bit of Goto’, so to speak – as the Push+ can still be slewed manually, as is common with Dobsonian telescopes, but also using your smartphone and built-in fine-step encoder in the telescope,

The high-resolution encoders allow the system to take you to any astronomical object you desire. Your smartphone functions as a display screen and at the same time orients you in the night sky. A crosshair shows you the position of your telescope in real time. You can decide, at any time, whether you want to use the push-to-system or prefer to control the telescope completely manually – it’s nice to have the choice!

Omegon Dobson Teleskop Push+ mini N 150/750 Pro

The Omegon Push+ is available with a 200mm (8″) OTA or as a Push+ Mini with a 150mm (6″) OTA:

Omegon Push+ mini N 150/750 Pro Dobsonian telescope
Omegon Push+ mini N 150/750 Dobsonian telescope
Omegon Push+ mini N 150/750 Skywatcher Dobsonian telescope

ASIAIR – astrophotography has never been so easy!

December 17 2018, Elias Erdnüß

The brand ZWO is, especially thanks to its powerful and user-friendly CMOS astrocameras, a frequently heard name in amateur astronomy.

With the ASIAIR control unit, ZWO now promises to fundamentally change the astrophotography scene! It’s a compact computer (Raspberry Pi), that is secured to the telescope of the mount. The device can do everything you expect a computerised telescope system of the 21st century to do!

Mount, camera, filter wheel, and autoguider are connected with the ASIAIR. Via an app for Android or iOS, everything can be controlled centrally and wirelessly via WLAN from the smartphone or tablet. You’ll no longer need to take your laptop with you to autoguide and to use cooled astrocameras. There are also advanced functions such as plate solving at the press of a button.

 

 

ASIASI communicates with the telescope mounts via the instrument neutral distributed interface (INDI) and so is compatible with most available GoTo mounts. The only snag: The device only supports ZWO cameras, autoguiders and filter wheels.

Other manufacturers like PrimaLuceLab with the EAGLE 2 are following similar approaches to computerisation. This one may feature higher performance and a wider range of functions, but there’s also the user-friendly ASIAIR for just a fraction of the price.

Omegon MiniTrack LX2 Receives „Hot Product 2019“ Award

December 10 2018, Marcus Schenk

The Omegon MiniTrack LX2 is the world’s first fully-mechanical photo mount for wide-field astrophotography.  With just a simple twist, you can capture amazing photos of the Milky Way.  This year the LX2 has received the much coveted astronomy award “Hot Product 2019” that the magazine Sky & Telescope awards annually to especially innovative products.

The Omegon Mini Track LX2 (or the set with the photography ball-head) makes a great gift for beginners and nature photographers, who would like to capture the night sky along with an amazing landscape.  If you have already tried with traditional means, but have not been satisfied with the results, the Mini Track LX2 is much simpler.  The proof is easy to see, if you look at the many amazing photos take with the LX2 and posted on social media.

More info about the Mini Track LX2 mount is available here. Gift-giving during this holiday season will be a piece of cake with the Mini Track LX2.

 

Below, you can read up on other, special products in our assortment, which have also received the “Hot Product” seal of approval:

The Mead Deep Sky Imager IV

The new and improved Planetary and Deep Sky Camera from Meade has convinced reviewers.  With a 16 megapixel Panasonic CMOS-Sensor, thermoelectric cooling, USB 3.0 and 3.8 µm pixels, the camera is a strong multi-use device for astrophotographers, who want to limits in their photography.  The new Deep-Sky-Imager IV is available in color or monochrome.  The software SkyCapture makes other programs superfluous and you can use if for all your photographic purposes.  The software runs on Windows and MacOS, as well as Linux.

Meade Deep-Sky-Imager DSI IV

Meade Deep-Sky-Imager DSI IV

 

Hubble Optics N 607/2012 UL24 f/3.3 Premium Ultra-Light DOB

“BIG DOB TO GO” is the moniker Sky & Telescope gave to the huge 24” Truss Dobson from Hubble Optics.  And for good reason.  The telescope can be broken down into individual pieces and transported in even the most compact vehicles.  Just imagine taking a telescope, as big as in many observatories, to the mountains or to a nice dark pasture.  You are sure to have quite the stargazing experience!

 

Hubble Optics Dobson Teleskop N 607/2012 UL24 f/3.3 Premium Ultra Light DOB

The Hubble Optics Ultra Light Dob with 607mm Aperture

 

Celestron Telescope Astrograph S 203/400 RASA 800 OTA

A digital Schmidt Camera for wide-angle photos!  The Celestron Astrograph RASA takes photos 20 times faster, than a Schmidt-Cassergrain Telescope.  The results are awe-inspiring photos of large-scale celestial objects. In 30 seconds, you can capture, what would require 10 minutes with a f/10 telescope.

 

RASA 8

The Astrograph 203/400mm RASA

 

iOptron Mount CEM120 GoTo

The heaviest mount from iOptron can handle instruments up to 52 kg and is fully LAN and Wifi remote capable.  In spite of its size, the mount moves smoothly like a hot knife through butter.

CEM 120 Montierung

The heavy-duty CEM 120 Mount

 

Daystar SS60-DS Solar Telescope

A compact solar telescope with 60mm aperture for safe solar viewing in H-alpha.  Daystar integrated a double stack Etalon Filter from the QUARK series into this refractor, which meanwhile has written a little success story of its own in solar observing.  Here, you get everything in one package, with which you can see solar protuberances, filaments and flares – everything that raises the pulse of a solar observer.  Attaching a camera to the helical focuser and you can capture your observations for good.

Daystar Sonnenteleskop SS60-DS

DayStar-Solar Telescope ST 60/930mm SolarScout SS60-DS H-Alpha

 

Celestron Smartphone Adapter

The easy way to connect your smartphone to your telescope with the Celestron Smartphone Adapter, which can be adjusted with precision on three axes.  Now you can easily position your smartphone’s camera over the eyepiece.

Celetron Smartphone Halterung

Celetron Smartphone Adapter NexYZ

 

 

Lunatico Pocket CloudWatcher

The Pocket CloudWatcher keeps an eye on the clouds on your behalf.  This weather and cloud detection device, which alerts you, when something changes in the sky.  The mobile CloudWatcher measures temperatures, brightness, relative humidity, dewpoint and alerts you immediately on your smartphone, when clouds move in.  The perfect gift for astrophotographers.

Cloud Watcher

Lunatico Pocket CloudWatcher

 

A few years ago, but still a great device:

Hot Product 2017: Universe2go

This AR Planetarium, which shows you and simultaneously explains the night sky.  There is no need to spend your time with star charts and books.  Universe2go is like a visit to the planetarium, but all in a handheld viewer that augments your reality.  Just download the free app, put your smartphone into the viewer and look up into the night sky.  The magazine Sky & Telescope was so enthusiastic about Universe2go that it received the Hot Product 2017 Award.

 

Omegon Handheld Planetarium Universe2go

The advantages?

  • Your impression of the real starry night sky gets an overhaul with a superimposed digital picture.
  • Learn about all 88 constellations and numerous celestial objects
  • Where are the planets? With Universe2go, you can find them all!
  • Over 3 hours of audio explanations, which will make you an expert of the night sky.
  • Many more features!

In the current issue, Sky & Telescope introduced many more products in the Hot Product category.